Variklio pašildymo sistema dėl Lexus IS (XE2) 11.2005 - 2009
Variklio pašildymo sistema dėl Lexus IS (XE2)
- Standartinis katalogas
- Naujasis katalogas (prekių: 3)
Power:
Matmenys:
Garums:
Visi filtrai
Power consumption:
Connector diameter:
3 gaminiai (-ių) daugiau naujame kataloge
Atkreipkite dėmesį: naujajame kataloge rasta daugiau dalių dar 3
Rasti rezultatai: 10
ENGINE HEATER TT-THERMO 1000XC ( READY-TO-INSTALL)
Dalies numeris:
AL51314717
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
157.50-12%137.84 eur -
-
157.50 - Kaina su nuolaida
- 137.84 eur
-
- Sutaupote 19.66 eur (-12%)
-
- parduotuvėje
- 3 vnt
-
pristatymo data:
29.03.2024, 03:39
- Įdėti į krepšelį
BŪTENT
-Heater intended for 4-6 cyl. engines.
TT-Thermo XC is the only hose-heater model on the market where the liquid and electrical sides are completely separate due to the patented design. This design maximizes the electrical safety of the device, and makes the model exceptional in the market.
- Ready-to-install package includes TT-THERMO 1000XC heater, Defa compatible element cable / socket 1.5m and Defa compatible 2.5m heating cable. (The color of the cable may differ from the picture)
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
TT-Thermo XC is the only hose-heater model on the market where the liquid and electrical sides are completely separate due to the patented design. This design maximizes the electrical safety of the device, and makes the model exceptional in the market.
- Ready-to-install package includes TT-THERMO 1000XC heater, Defa compatible element cable / socket 1.5m and Defa compatible 2.5m heating cable. (The color of the cable may differ from the picture)
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
Splashproof connection cable
Dalies numeris:
AL14332844
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
29.33-13%25.46 eur -
-
29.33 - Kaina su nuolaida
- 25.46 eur
-
- Sutaupote 3.87 eur (-13%)
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
05.04.2024, 11:55
- Įdėti į krepšelį
Connector: |
|
Current: |
Max 16A
|
Garums: |
1,5M
|
Spriegums: |
AC 220-240 V
|
BŪTENT |
DEFA PlugIn connectors do not require any tools to make a safe connection. Therefore, you can install them without the help of a qualified electrician.
cable 1.5m
Defa compatible heating cable - Locking fork connection
Dalies numeris:
AL33773500
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
37.50 eur
- Kaina: 37.50 eur
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
05.04.2024, 11:55
- Įdėti į krepšelį
BŪTENT
Defa compatible instrument socket / element cable - Defa compatible heating cable - Locking fork connection
ENGINE HEATER TT-THERMO 500XC ( READY-TO-INSTALL)
Dalies numeris:
AL73974230
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
138.75-12%122.29 eur -
-
138.75 - Kaina su nuolaida
- 122.29 eur
-
- Sutaupote 16.46 eur (-12%)
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
05.04.2024, 11:55
- Įdėti į krepšelį
BŪTENT
-Heater intended for 1-3 cyl. engines.
TT-Thermo XC is the only hose-heater model on the market where the liquid and electrical sides are completely separate due to the patented design. This design maximizes the electrical safety of the device, and makes the model exceptional in the market.
- Ready-to-install package includes TT-THERMO 500XC heater, Defa compatible element cable / socket 1.5m and Defa compatible 2.5m heating cable. (The color of the cable may differ from the picture)
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
TT-Thermo XC is the only hose-heater model on the market where the liquid and electrical sides are completely separate due to the patented design. This design maximizes the electrical safety of the device, and makes the model exceptional in the market.
- Ready-to-install package includes TT-THERMO 500XC heater, Defa compatible element cable / socket 1.5m and Defa compatible 2.5m heating cable. (The color of the cable may differ from the picture)
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
ENGINE HEATER TT-THERMO 1000XC
Dalies numeris:
AL33724026
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
149.17-14%128.29 eur -
-
149.17 - Kaina su nuolaida
- 128.29 eur
-
- Sutaupote 20.88 eur (-14%)
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
05.04.2024, 11:55
- Įdėti į krepšelį
Power: |
1000 W
|
Matmenys: |
150 mm x 90 mm x 80 mm
|
Pipe diameter: |
⏀16 mm - ⏀20 mm
|
Connector diameter: |
17 mm
|
Pump throughput capacity: |
8 l/min
|
Power consumption: | ALL PROPERTIES |
Power consumption: |
4,3 A
|
Frequency: |
50/60 Hz
|
Spriegums: |
AC 220-240 V
|
BŪTENT |
A device that allows you to warm up the engine without starting it. Designed to preheat the engine, to facilitate starting the engine in cold weather and, in some cases, to warm the air in the vehicle cabin.
Weight 0.95 kg
Dimensions Length 150 mm Width 95 mm Height 95 mm
Voltage AC 220-240 V
Frequency 50/60 Hz
Power 1000 W
Power consumption 4.3 A
Compatibility Defa
Connector diameter 16 mm
Manufacturer TT-THERMO
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
ENGINE HEATER TT-THERMO 1500XC ( READY-TO-INSTALL
Dalies numeris:
AL51314719
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
155.83-12%136.38 eur -
-
155.83 - Kaina su nuolaida
- 136.38 eur
-
- Sutaupote 19.45 eur (-12%)
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
05.04.2024, 11:55
- Įdėti į krepšelį
BŪTENT
-Heater intended for 6+ cyl. engines.
TT-Thermo XC is the only hose-heater model on the market where the liquid and electrical sides are completely separate due to the patented design. This design maximizes the electrical safety of the device, and makes the model exceptional in the market.
- Ready-to-install package includes TT-THERMO 1500XC heater, Defa compatible element cable / socket 1.5m and Defa compatible 2.5m heating cable. (The color of the cable may differ from the picture)
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
TT-Thermo XC is the only hose-heater model on the market where the liquid and electrical sides are completely separate due to the patented design. This design maximizes the electrical safety of the device, and makes the model exceptional in the market.
- Ready-to-install package includes TT-THERMO 1500XC heater, Defa compatible element cable / socket 1.5m and Defa compatible 2.5m heating cable. (The color of the cable may differ from the picture)
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
ENGINE HEATER TT-THERMO 1500XC
Dalies numeris:
AL30750421
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
157.17-12%138.69 eur -
-
157.17 - Kaina su nuolaida
- 138.69 eur
-
- Sutaupote 18.48 eur (-12%)
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
05.04.2024, 11:55
- Įdėti į krepšelį
Power: |
1500 W
|
Matmenys: |
151 mm x 90 mm x 75 mm
|
Garums: |
151 mm
|
Pipe diameter: |
⏀16 mm - ⏀20 mm
|
Connector diameter: |
17 mm
|
Weight: | ALL PROPERTIES |
Weight: |
880g
|
Pump throughput capacity: |
8 l/min
|
Power consumption: |
6,2 A
|
Frequency: |
50/60 Hz
|
Spriegums: |
AC 220-240 V
|
BŪTENT |
The genuine and original TT-Thermo engine heater is suitable for almost all motor vehicles!
New generation hose heater with circulating water pump. Power 1500W
Externally more compact in size than previous Kld2 models
Our only model that is completely free to install in any position. No limited mounting angle or position
The resistors inside the heat exchanger are not directly in the liquid, so the resistors do not burn from the air bubbles in the system
Pump bearings reinforced and improved
Improved pump performance
All experiences of previous models have been taken into account in the design
Higher quality materials and components
Designed in Finland
Defa compatible connector
Hose outlet diameter 17mm
You can find the hose bends that may be needed for installation in our online store
Forget the inefficient engine heater!
Weight 0.95 kg
Dimensions Length 150 mm Width 95 mm Height 95 mm
Voltage AC 220-240 V
Frequency 50/60 Hz
Power 1500 W
Power consumption 4.3 A
Compatibility Defa
Connector diameter 16 mm
Manufacturer TT-THERMO
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
TT-THERMO 2200XC 18mm
Dalies numeris:
AL51314701
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
164.83 eur
- Kaina: 164.83 eur
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
05.04.2024, 11:55
- Įdėti į krepšelį
BŪTENT
Designed for large machines such as work vehicles, trucks, etc.
New generation heater with water circulation pump. Power 2200W, adjustable connection angle.
No restrictions on installation angle or position
Defa compatible connector
Adjustable connection angle
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
New generation heater with water circulation pump. Power 2200W, adjustable connection angle.
No restrictions on installation angle or position
Defa compatible connector
Adjustable connection angle
Pre-starting electric engine heaters are a solution for cars in times of cold and frost. Comfort - for you, care - for your car.
A cold engine start, for example in 30 degree frost, is equivalent to 500 km of vehicle mileage. In a cold engine, the viscosity coefficient of the lubricant becomes higher, and the load on the equipment increases.
How does cold starting a car affect the life of the starter? - For several reasons, during a cold start, the starter is the first to suffer: Thickened oil makes it difficult for the crankshaft to rotate. The battery uses more energy to start the engine. Gasoline evaporates more slowly and does not ignite easily. The viscosity of diesel fuel increases, making it more difficult for it to leak into the combustion chamber.
Engine wear during cold starts: Due to frequent cold starts, they contribute to more expensive repairs than replacing the starter and battery. The problem is that at negative temperatures all components lose volume, and the gap between the parts increases slightly. Therefore, cold starting a car helps reduce compression, as more fuel goes into the crankcase between the piston rings and the cylinder walls. Increased fuel consumption is not as bad as its consequences, because the more gasoline or diesel fuel gets into the engine oil, the faster the lubricant loses its properties. Therefore, if you frequently cold start the engine, wear is guaranteed on the following parts: crankshaft journals; main and connecting rod bearings; crankshaft support bearings.
All these parts are lubricated by engine oil, and if it loses its properties, the wear of these components accelerates.
All this together leads to the fact that cold starting a car negatively affects the life of the starter. Due to increased energy consumption and excessive load, the likelihood of insulation breakdown between the windings or their complete failure increases.
A pre-starting, electric engine heater will help solve the problem. We suggest you purchase a ready-made version of the pre-start engine system, which includes all the necessary equipment and simple installation instructions.
How to make starting a cold engine safe? – Install pre-starting electric engine heaters! Take care of your iron friend.
TT-THERMO 2200XC 20mm
Dalies numeris:
AL35880284
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
188.33-5.9%177.21 eur -
-
188.33 - Kaina su nuolaida
- 177.21 eur
-
- Sutaupote 11.12 eur (-5.9%)
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
05.04.2024, 11:55
- Įdėti į krepšelį
BŪTENT
A new generation hose heater with a circulating water pump. Power 2200W, adjustable angle in connection.
Intended for large machines, such as work machines, trucks, etc.
Externally more compact than previous Kld2 models
Our only model that is completely free to install in any position
No limited installation angle or position
The resistors inside the heat exchanger are not directly in the liquid, therefore the resistors do not burn from air bubbles in the system
Pump bearing strengthened and improved
Improved pump performance
All the experiences of previous models have been taken into account in the design
Higher quality materials and components than before
Designed in Finland
Defa compatible connector
Adjustable angle at the connection
You can find the hose bends that may be needed for the installation in our online store.
Forget the inefficient radiant heater!
Intended for large machines, such as work machines, trucks, etc.
Externally more compact than previous Kld2 models
Our only model that is completely free to install in any position
No limited installation angle or position
The resistors inside the heat exchanger are not directly in the liquid, therefore the resistors do not burn from air bubbles in the system
Pump bearing strengthened and improved
Improved pump performance
All the experiences of previous models have been taken into account in the design
Higher quality materials and components than before
Designed in Finland
Defa compatible connector
Adjustable angle at the connection
You can find the hose bends that may be needed for the installation in our online store.
Forget the inefficient radiant heater!
Laidų komplektas, variklio pašildymo sistema DEFA 460785
Dalies numeris:
AL12650829
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
78.56 eur
- Kaina: 78.56 eur
-
- vienetų pas tiekėją
- 5 vnt
-
pristatymo data:
03.04.2024, 13:55
- Į naująjį katalogą
Žr. informaciją apie prekę naujajame kataloge
Laidų komplektas, variklio pašildymo sistema DEFA 460785
Dalies numeris:
AL22971655
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
110.66 eur
- Kaina: 110.66 eur
-
- vienetų pas tiekėją
- 3 vnt
-
pristatymo data:
29.03.2024, 13:55
- Į naująjį katalogą
Žr. informaciją apie prekę naujajame kataloge
Laidų komplektas, vidaus šildymo vent., (variklio paš.sist.) DEFA 460766
Dalies numeris:
AL33712806
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
175.38-30%122.24 eur -
-
175.38 - Kaina su nuolaida
- 122.24 eur
-
- Sutaupote 53.14 eur (-30%)
- tiekėjo likutis: NETURIME
- Į naująjį katalogą
Žr. informaciją apie prekę naujajame kataloge
ENGINE HEATER TT-THERMO 1500KLD
Dalies numeris:
AL14332360
-
Pristatome į
United StatesŠį produktą galime pristatyti į United States ir kitas šalis. Pristatymo kainą galite matyti pirkinių krepšelyje.
Mes turime įvairių tiekimo į United States variantų. Pristatymo datą ir kainą rasite pirkinių krepšelyje.
Savo siuntą galite sekti su paskirtąja sekimo nuoroda, kurią gausite iškart apmokėję savo užsakymą. -
117.50 eur
- Kaina: 117.50 eur
- tiekėjo likutis: NETURIME
Fluid: |
Coolant, Glycol - G11, G12
|
Power cord: |
DEFA compatible cables
|
Power: |
1500 W
|
Matmenys: |
150 mm x 90 mm x 80 mm
|
Pipe diameter: |
⏀16 mm - ⏀20 mm
|
Connector diameter: | ALL PROPERTIES |
Connector diameter: |
⏀16 mm -⏀17 mm
|
Weight: |
880g
|
Pump throughput capacity: |
8 l/min
|
Power consumption: |
6,2 A
|
Frequency: |
50/60 Hz
|
Spriegums: |
AC 220-240 V
|
BŪTENT |
installation options than the model with a direct hose connection. The connection of the heater to the electricity network is
With a connector compatible with the Defa system. If the need for installation length to the one in the car
to the electric cable system is long, we also have Defa-compatible armored 1.5m available separately
long extension cord.
The operating principle of the heater is simple: it simultaneously heats and circulates the coolant
in the engine. Therefore, the engine heats up evenly everywhere and the vehicle's interior quickly when the vehicle is started.
Thanks to the even heating of the engine, the heater is also excellently suitable for new vehicles that do not
can use a traditional block heater.
The heater is easy to install and reliable. In general, the best place for installation is the water hose between the engine and the interior heater. The heater has a built-in thermostat that keeps the temperature at +65..+75
degree. The pump circulates the heated liquid all the time. In this way, the heat is efficiently transferred to the engine. Thanks to the thermostat, the heater can be turned on without the risk of overheating.
Delivery includes: Engine heater with Defa-compatible connector, water hose clamps, installation and user manual in Finnish.
Deliveries directly from the warehouse of the importer Suomen Tuontiekniikka Oy. Delivery time 2-5 days.
The heater is CE-marked and has a 1-year warranty from the date of purchase.
Technical information:
Voltage AC 220-240 V
Frequency 50/60 Hz
Power 1500 W
Power consumption 6.2 A
Power cord Defa compatible cables
Pump capacity 8 l/min
Fluid Coolant, Glycol - G11, G12
Dimensions 150 mm x 90 mm x 80 mm
Weight 880 g (without power cord)
Connections Ø 16 mm – shoulder Ø 17 mm
Hoses Internal diameter
Ø 16 mm – 20 mm
Visos „Lexus IS (XE2)“ dalys
- Nebegaminamos dalys
- Kėbulo dalys
- Bamperis
- Sparnas
- Plastikinis vidinis sparnas
- Buferio grotelės
- Grotelės
- Kapotas
- Galinio rato arkaNEW!
- Buferio laikiklis
- Vilkimo kablys
- Priekinis įtaisų skydelis
- Tempimo kablysNEW!
- Priekinio buferio spoileris
- Priekinio žibinto rėmasNEW!
- Sparno moldingasNEW!
- Durų lankstasNEW!
- Grotelių rėmelis
- Priekabos prikabintuvasNEW!
- Priekinio stiklo plokštėNEW!
- Apsauginė plėvelė
- Numerio laikiklis
- Žibintai
- Pagrindinis priekinis žibintas
- Galinis žibintas
- Šoninis posūkis
- Priekinis rūko žibintas
- Atspindintis elementas
- Balastas
- Lemputė, durų lemputėNEW!
- Kabelių remonto komplektas, priekinis žibintasNEW!
- Priešrūkiniiai žibintai +uždengimaiNEW!
- Atšvaitas, padėtis/atšvaitasNEW!
- Lemputė, skaitymo apšvietimasNEW!
- Lemputės lizdas, priekinis žibintas
- Priekinio žibinto uždengimas
- Lemputė
- Universalus galinis žibintas
- Automobilių puošybos dalys
- Veidrodžiai ir jų dalys
- Stabdžių sistemos
- Stabdžių trinkelėsNEW!
- Stabdžio diskasNEW!
- Remonto komplektas, stabdžių apkabaNEW!
- Stabdžių apkabaNEW!
- Stabdžių diskų kaladėlėsNEW!
- Trosas, stovėjimo stabdysNEW!
- Kreipiančiųjų movų rinkinys, stabdžių apkabaNEW!
- Stabdžių žarnelėNEW!
- Remonto rinkinys, stabdžių kaladėlėsNEW!
- Pagrindinis stabdžių cilindrasNEW!
- Stabdžių žibinto jungiklisNEW!
- Stūmoklis, stabdžių apkabaNEW!
- Vakuumo siurblys, stabdžių sistemaNEW!
- Girgžd. slopinanti folija, stabdžio antd. (sankab. gaubtas)NEW!
- Trosas, darbinis stabdysNEW!
- Vairo dalys
- Valdymo rankena
- Stabilizatoriaus statramstisNEW!
- Skersinės vairo trauklės antgalisNEW!
- Šakės šarnyrasNEW!
- Sailentbloko įvorėNEW!
- Stabilizatoriaus įtvarasNEW!
- Ašies jungtisNEW!
- Vairo traukėNEW!
- Vairo traukės apsaugaNEW!
- Prikabinimo svirtisNEW!
- Remonto komplektas, rato pakabaNEW!
- Išvirtimo reguliavimo varžtasNEW!
- Pakabos remonto rinkinysNEW!
- Manžetų rinkinysNEW!
- Montavimas, amortizatoriaiNEW!
- Montavimas, diferencialasNEW!
- Vairo trauklės įvorėNEW!
- Remonto komplektas, atrama/vairo trauklėNEW!
- Stebulės laikiklio įvorėNEW!
- Gnybtas, atraminis buferis (ašies korpusas)NEW!
- Elektros sistemos dalys
- Uždegimo žvakėNEW!
- ABS daviklisNEW!
- Alkūninio veleno padėties jutiklisNEW!
- Kuro pompaNEW!
- Uždegimo ritėNEW!
- Kintamosios srovės generatoriusNEW!
- Siuntimo blokas, aušinimo skysčio temperatūraNEW!
- Lambda jutikliai
- StarterisNEW!
- Pakaitinimo žvakė
- Jutiklis, statymo atstumo jutiklis
- Siuntimo blokas, alyvos slėgisNEW!
- Oro srauto daviklis
- Įpūtimo slėgio jutiklisNEW!
- Stabdžių žibinto jungiklisNEW!
- Jungiklis, atbulinės eigos žibintasNEW!
- Oro pagalvės ritėNEW!
- Siuntimo blokas, įsiurbiamo oro temperatūraNEW!
- Jutiklis, išmetimo slėgisNEW!
- Detonacijos jutiklisNEW!
- Jutiklis, išmetamųjų dujų temperatūraNEW!
- Jutiklis, ksenono žibintai (žibintų diapazono reguliavimas)NEW!
- Aukšto slėgio siurblysNEW!
- Laikiklis, angliniai šepetėliaiNEW!
- RPM jutiklis, automatinė transmisijaNEW!
- Laisvos eigos pavara, starterisNEW!
- Elektros blokas, grąžulasNEW!
- Diržų komplektas, statymo atstumo jutiklisNEW!
- Jutiklis, degalų temperatūraNEW!
- Kamštis, ritėNEW!
- Vandens siurblys, priekinio stiklo plovimasNEW!
- Relė, pavojaus žibintaiNEW!
- Lygintuvas, kintamosios srovės generatoriusNEW!
- Skriemulys, kintamosios srovės generatoriusNEW!
- RPM Sensor, engine managementNEW!
- Oro srauto jutiklisNEW!
- Kaitinimo žvakė, papildomas šildytuvasNEW!
- Jungiklis, stabdžių pavara (variklio paskirstymas)NEW!
- Pavarų perjungimo vožtuvas, automatinė transmisijaNEW!
- Galinio vaizdo kamera, statymo atstumo jutiklisNEW!
- Valdymo blokas, elektrinis ventiliatorius (variklio aušinimaNEW!
- Ritė, uždegimasNEW!
- Valdymo blokas, pneumatinė pakabaNEW!
- Montavimo komplektas, variklio pašildymo sistemaNEW!
- Akumuliatoriaus įkroviklis
- Akumuliatorius
- Akumuliatorių krovikliai
- Asortimentas, kaiščio korpusas
- Battery booster/Jump starter
- Elektrinių įr. priedai
- Inverteris
- Jumper cables
- Saugiklių rinkinys
- Siuntimo blokai/jutikliai
- Terminės dalys
- TermostatasNEW!
- Radiatorius
- Vandens siurblysNEW!
- Salono ventiliatorius
- Radiatoriaus dangtelis
- Kondicionieriaus radiatorius
- Plėtimosi rezervuaras
- Kondicionieriaus kompresoriusNEW!
- ŠildytuvasNEW!
- Radiatoriaus ventiliatorius
- Tepalų talpos dangtelis
- Tepalų radiatorius
- DžiovintuvasNEW!
- Magnetinė sankaba, oro kondicionieriaus kompresoriusNEW!
- Slėgio jungiklis, oro kondicionavimasNEW!
- Plėtimosi vožtuvasNEW!
- Valdymo blokas
- Tarpiklis, termostatasNEW!
- Tarpiklis, EGR vožtuvasNEW!
- AntifrizasNEW!
- Jungė
- Air conditioning bearing
- O-Ring rinkinys
- R134a
- Variklis
- Alyvos išleidimo kaištis, alyvos karterisNEW!
- Tarpiklis, svirties dangtisNEW!
- Tarpiklis, cilindro galvaNEW!
- Tarpiklių komplektas, cilindro galvaNEW!
- Pavaros grandinės komplektasNEW!
- Veleno sandariklis, alkūninis velenasNEW!
- Varžtų kompl., cil. galvutės varžtaiNEW!
- Tarpiklis, įsiurbimo kolektoriusNEW!
- Kompresoriaus padavimo žarnaNEW!
- Tarpiklių komplektas, svirties gaubtasNEW!
- Tarpiklis, išleidimo kolektoriusNEW!
- Stūmoklio žiedų komplektasNEW!
- Skriemulys, alkūninis velenasNEW!
- Išleidimo vožtuvasNEW!
- Tarpiklių komplektas, vožtuvo šerdisNEW!
- Montavimo komplektas, kompresoriusNEW!
- Įleidimo vožtuvasNEW!
- Vožtuvas, variklio bloko alsuoklisNEW!
- Alyvos siurblysNEW!
- Svirtis/kumštelisNEW!
- Tarpiklių rinkinys, variklio karterisNEW!
- Karteris (variklio)NEW!
- Valdymo vožtuvas, skirstomojo veleno reguliatoriusNEW!
- Visas tarpiklių komplektas, variklisNEW!
- Pavaros grandinėNEW!
- Slegio keitiklis, išmetimo valdymasNEW!
- Tarpiklis, vožtuvo šerdisNEW!
- Vožtuvų kreiptuvaiNEW!
- Pavaros svirtis, vožtuvų eilėNEW!
- Tarpiklis, įsiurbimo kolektoriaus korpusasNEW!
- Tarpiklis, termostatasNEW!
- Skirstomojo veleno reguliatoriusNEW!
- Tarpiklis, slyvos pildymo angos dangtelisNEW!
- Švaistiklio guolių rinkinysNEW!
- Veleno sandariklis, skirstomasis velenasNEW!
- Grandinė, alyvos siurblio pavaraNEW!
- Tarpiklis, alyvos siurblysNEW!
- Pavaros svirtis, vožtuvų eilėNEW!
- Alkūninio veleno guolių rinkinysNEW!
- Tarpiklis, žvakių dėklasNEW!
- Pagrindinis surinkimas, guolisNEW!
- Tarpiklis, įsiurbimo / išleidimo kolektoriusNEW!
- Atraminis tarpiklis, alkūninis velenasNEW!
- Priedų komplektas, stūmiklisNEW!
- Svirčių komplektas, variklio valdymasNEW!
- Veleno sandariklis, skirstomasis velenasNEW!
- Skirstomoji dėžėNEW!
- Cilindro įvorės tarpiklisNEW!
- Tepimo vamzdelis, piršto tepimasNEW!
- Tarpiklis, turbinos įvadas (piltuvas)NEW!
- Važiuoklės sistemos dalys
- Ratų guolių rinkinysNEW!
- GranataNEW!
- AšisNEW!
- Granatos apsauginis gaubtasNEW!
- Veleno sandariklis, diferencialasNEW!
- Sandariklis, kardaninis velenasNEW!
- Guolis, kardaninio veleno centrinis guolisNEW!
- Veleno sandariklis, neautomatinė transmisijaNEW!
- Ašies veržlė, kardaninis velenasNEW!
- Guolis, kardaninis velenasNEW!
- Kardaninis velenasNEW!
- Jungtis, vairavimo velenasNEW!
- Alyva, visų ratų pavaros plokšt. formos sankabaNEW!
- Alyvos tarpiklis, neautomatinė pavarų dėžėNEW!
- Diržai ir skriemuliai
- V formos rumbuoti diržaiNEW!
- Įtempiklio skriemulys, paskirstymo diržasNEW!
- Kreipiantysis skriemulys, V formos rumbuotas diržasNEW!
- Įtempiklio svirtis, V formos rumbuotas diržasNEW!
- V formos rumbuotas diržas, komplektasNEW!
- Generatoriaus skriemulys
- V formos rumbuoti diržaiNEW!
- Alkūninio veleno skriemulių rinkinysNEW!
- Kreipiantysis skriemulys, V formos diržasNEW!
- Įtempiklio skriemulys, V formos diržasNEW!
- Variklio, pavarų dėžės ir važiuoklės sistemos tvirtinimo dalys
- Automobilių salono įranga
- Oro įsiurbimo sistemos dalys
- Montavimo komplektas, kompresoriusNEW!
- Kompresorius, įkrovimo sistema
- Droselio korpusasNEW!
- Tarpiklis, turbinos oro žarnaNEW!
- Tarpiklis, kroviklisNEW!
- Pagrindinis surinkimas, guolisNEW!
- Montavimo pasta, dyzelinis injektorius / kaitinimo žvakėNEW!
- Srieginis varžtas, įkroviklisNEW!
- Valdymo vožtuvas, kompresoriusNEW!
- Skirtingo slėgio jutiklisNEW!
- Dujų išmetimo sistema
- Katalizatoriaus keitiklisNEW!
- Tarpiklis, išleidimo kolektoriusNEW!
- Guminė juosta, išmetimo sistemaNEW!
- Montavimo komplektas, kompresoriusNEW!
- Tarpiklis, išleidimo kolektoriusNEW!
- Suodžių / kietųjų dalelių filtras, išmetimo sistemaNEW!
- Varžtas, išmetimo sistemaNEW!
- Atraminis buferis, triukšmo slopintuvasNEW!
- Spyruoklė, duslintuvasNEW!
- Spyruoklė, išmetimo vamzdisNEW!
- Pagrindinis surinkimas, guolisNEW!
- Montavimo komplektas, išmetimo sistemaNEW!
- Tarpiklis, alyvos išleidimo anga (pildymas)NEW!
- Vožtuvas, EGR išmetimo valdymasNEW!
- Perjungimo vožtuvas, išmetamųjų dujų vožtuvasNEW!
- Slėgio vamzdelis, slėgio jutiklis (suodžių/dalelių filtras)NEW!
- Degalų sistemos dalys
- ERG vožtuvasNEW!
- Droselio korpusasNEW!
- Detonacijos jutiklisNEW!
- Tarpiklis, purkštuko laikiklisNEW!
- Jutiklis, išmetamųjų dujų temperatūraNEW!
- Slegio keitiklis, išmetimo valdymasNEW!
- Tarpiklis, purkštukasNEW!
- Slėgio kontrolės vožtuvas, bendros linijos sistemaNEW!
- Tarpiklių rinkinys, purkštuko antgalisNEW!
- Valdymo vožtuvas, kuro talpa (įprasta magistralinė sistema)NEW!
- Oro slėgio jutiklis, aukščio adaptacijaNEW!
- Kuro siurblysNEW!
- Spaustuvai ir tvirtinimo dalys
- Montavimo elementas
- Sąvarža, atšvaitas / apsaugos juostaNEW!
- Dangtelis
- Buferis, gaubtasNEW!
- Veržlė, pasukamasis kakliukasNEW!
- Jungėjas
- Kniedė
- Kniedė
- Kniedžių rinkinys
- Laidų tvirtinimo detalės
- Smeigė
- T-jungtis
- Tvirtinimo apkaba
- Tvirtinimo korpusas
- Tvirtinimo tarpinė
- Universalūs gnybtai
- Varžtas
- Varžtas
- Veržlė
- Žarnos spaustukas
- Serviso įranga
- Kitos
- TarpiklisNEW!
- GnybtasNEW!
- Variklio alyvaNEW!
- Priekinis stiklasNEW!
- Alyva, automatinė pavarų dėžėNEW!
- Montavimo komplektas, kardaninio veleno gofruotoji membranaNEW!
- Alyva, automatinė pavarų dėžėNEW!
- Laisvumo reguliatoriusNEW!
- Šoninis langasNEW!
- Pavara, įpurškimo siurblysNEW!
- Tarpiklis, neautomatinės pavarų dėžės korpusasNEW!
- Tarpiklis, alyvos pildymo anga (piltuvas)NEW!
- Montavimo įrankių komplektas, sankaba / smagratisNEW!
- Dangtelis, stabdžių apkabaNEW!
- Alyvos filtro veržliaraktisNEW!
- Valdymo blokas, pneumatinė pakabaNEW!
- Akumuliatoriaus poliaus gnybtas
- Dangtelis, akumuliatoriaus poliaus gnybtas
- Garsinis signalas
- Kitos
- Maišelis
- Rankinė pompa
- Tr. priemonės kombinac. dažai
- Vielinis šepetys, akumuliatoriaus polių/gnybtų valymas
- Įžeminimo kabelis, skirstytuvas
- Šildymo sistemos
- Cheminiai produktai automobiliams
- Apsauginė alyva nuo korozijos
- Apsaugos nuo rūdžių gruntas
- Body cosmetics
- Exterior care
- Glass washing
- Glue
- Hand washing paste
- Interior cleaning
- Pirštinės
- Polish wax
- Pramoninės alyvos
- Priedas
- Radiatoriaus skystis
- Rankų priežiūra
- SPRAY PAINTS AND CRUNTS
- Spynų atitirpiklis
- Stabdžių skystis
- Technical fluids
- Universalus užpildas
- Valymo servetėlės
- Universalūs guoliai
- Chemija ir kosmetinės priežiūros reikmenys
- Priedai
- Accessories for mobile phones
- Apsauginiai akiniai
- Atšvaitas
- BOOSTER, Emergency Aid - Battery Bank
- Besisukantis švyturėlis
- Car flags
- Car seat covers
- Children's goods
- Cigarečių uždegiklis
- Clamps and ties
- Covers for car documents
- Electronic parking clock
- Fefrigerators and cooling boxes
- Gesintuvas
- Interior freshener
- Izoliacinė juosta
- Kastuvas
- Kempinė
- Kuro kanistras
- Laikrodžiai - indikatoriai
- Lamps
- Lamps LED
- Ledo grandiklis
- Lights XENON
- Lipdukas
- Mobile phone charger- powerbank
- Multimedia
- Multimetras
- Parking assistant system
- Parking clock
- Perspejamasis trikampis
- Pets
- Pirmosios pagalbos vaistinėlė
- Priedai
- Radijas
- Raktų žiedų rinkinys
- Rudder cover
- Ryškaus matomumo apdaras
- Stickers and car identification
- Stogo bagažinė
- Stogo bagažinė
- Tape
- Tempimo virvė
- Tint films for car
- Transporto priemonės plovimo šepetys
- Vakuuminiai dulkių siurbliai
- Vandens kanistras
- Ventiliatorius
- Vidinės kameros
- Vilkimo rutulio rėmas, grąžulas
- Winches
- Wipes
- Šviestuvai
- Jums taip pat turėtų patikti
- Šildymo sistemos
- Variklio pašildymo sistema
- Variklio pašildymo sistema dėl Lexus